SP1+Pro: Web-enabled, Pro environmental monitoring appliance 

with a built-in temperature sensor, 1x dry-contact I/O port, 1x sensor-port for an external sensor and an expanded feature-set 

SensorProbe1+ compact environmental monitoring appliance monitors and manages environmental, security and power conditions over IP, providing early warnings before critical events turn into a disaster.

sensorProbe1+ Pro (Temp.) (SP1+Pro) comes equipped with:
1x hard-wired temperature sensor on a 5 foot cable
1x intelligent sensor input
1x dry-contact I/O port

SensorProbe1+ monitors critical environmental conditions, such as temperature, humidity, liquid water presence, power, intrusion, and smoke with a simple, easy-to-use web interface. SensorProbe1+ allows you to connect an external AKCP sensor such as temperature sensor, thermal map or water leak detection to its intelligent sensor port. You may also connect the sensor splitter box with cabinet thermal maps and contactless current meter, and you have a complete monitoring solution for your rack. With SensorProbe1+ you can monitor temperature front and rear, top middle, and bottom. Check your humidity and current consumption. Utilize the dry contact for door contacts, and virtual sensors* to monitor third party devices installed in the rack.

When a sensor goes out of range of a configurable threshold, the system will notify you via email, web page, network management (SNMP), and/or SMS messages (via email-to-SMS). 

SP1+Pro comes with an enhanced set of software functions (see table).

Like with all other AKCP environmental monitors - running the same user interface as the rest of the sensorProbe+ product line - SensorProbe1+ allows users to keep an eye on remote conditions from a secure web interface and receive SNMP, E-mail, text message and voice call alert notifications when user-adjustable thresholds are exceeded.

The web interface provides an overview of environmental measurements with real time sensor data. All measurements are logged allowing users to collect data for trending and capacity management.

SensorProbe1+ offers secure access through the web and supports HTTP and HTTPS protocols. Easily view and log temperature, relative humidity / dew point and external sensors over the intranet or the Web. No software required - securely access the graphical user interface from a web browser.

SensorProbe1+ Pro offers flexible access rights and security settings with two password-protected access account levels for a User to view data, and for an Administrator to view data, edit thresholds and setup network settings.

SensorProbe1+ can also be powered with dual inputs, available through AKCP's external DC-DC conversion box.

sensorProbe1+ is manufactured using highly integrated, low power surface mount technology to ensure long term reliability.

Dry-Contact I/O Port
The I/O dry-contact port can serve either as an input port (On/Off state-reading), or as an output port (low milliamp 5VDC relay), user-determined via sensorProbe+'s Web interface.

When a dry-contact port is set to input mode, it works as a standard On/Off (state-reading) dry-contact input. A smoke alarm that has a dry contact output, for example, can be connected to an input dry-contact port, and sensorProbe+ will detect if the smoke detector is in alarm condition or not.

When a dry-contact port is set to output mode, it essentially behaves as a small relay that can output 5VDC with a few milliamps of current (although not enough to power anything or to drive a larger relay). An example would be perhaps a UPS that needs a signal to turn on. In output mode, sensorProbe+ will output 5VDC signal to the UPS dry contact input, telling it to turn on.

Under sensorProbe+ user-interface settings, Admin can choose if the contact is in input or output mode. If set as output, Admin can also set its normal condition to be high or low (+5VDC or 0VDC).

Admin can setup to control the output high-or-low condition by a notification which is controlled by a sensor. For example, if AC power is not detected, signal the dry contact output to turn high, which will then output 5VDC to the connected UPS telling it to turn on.

No Software Required
SensorProbe1+ is simple to install and use, requiring no special software other than a standard Web Browser. SensorProbe1+ connects to an Ethernet network with a standard RJ45 connector and sends data in standard TCP/IP packets. It is easily configured with a simple menu using a Web Browser. Pro version can be password protected with 2 access account level types: Administrator, and View Only. From within an Intranet or over the Internet, the user can securely access the monitoring appliance by entering its IP address.

Package Includes
1x sensorProbe1+ Pro with hard-wired temperature sensor on a 5 foot cable
1x external 100V~240V power adapter
5x virtual sensors

Need help? Call KVMGalore at 1-800-636-3434, or submit your question on KVMGalore HelpCenter.